Ditching Silicone: How Long Does a Dental Impression Take Digitally?

Ditching Silicone: How Long Does a Dental Impression Take Digitally?

A digital impression has three blocks of time, and only one of them is “scanning”.

Preparation comes first. The field needs to be as dry and visible as the case allows. Retraction, where the preparation needs it, is clinical time whether the record is silicone or a file. A scanner does not remove that step. It makes a poor field more obvious, because the gap appears on the screen.

The capture itself, on current budget scanners, is commonly described in seconds to a few minutes rather than in a long setting time. Dentiverse listings give two useful reference points, both as product claims to test rather than as promises. Panda Smart is described as capable of a full-arch scan in about one minute. Runyes specifications for the relevant 3DS model list about 30 seconds for a single arch and about 90 seconds for a full arch with occlusion. A quadrant crown in experienced hands is often shorter than a full arch. A new user is often slower than either figure for the first weeks.

Review is the third block, and it is the one clinics forget when they quote a scan time. The opposing arch, the bite, a second pass on a distal margin and a proper look at the mesh can add as much time as the first sweep. That time is well spent. It is still usually shorter than disposing of a set silicone impression and starting again.

So a fair answer to how long does a dental impression take, digitally, is: the scan pass is often one to a few minutes, and the appointment slot should also hold isolation, bite registration and an on-screen check. For many single restorations, teams find the chairside record comparable to a conventional impression, with the saving appearing when the first file is good enough to send.

Digital Impressions in Dentistry: How the Process Works

Digital impressions in dentistry replace the negative mould with a three-dimensional file. The clinician moves the scanner tip along a path. The software stitches the images into a model that can be rotated, stored and sent. The laboratory never waits for a courier to discover that a margin was short.

The process rewards a routine. Teams that scan “until it looks done” take longer and rescan more than teams with a set path: the prepared arch, the opposing arch, the bite, then a named check of the margins and the contacts.

From Intraoral Scanning to the Final Digital Model

The path from wand to model is short when each stage has a purpose.

The area is isolated and the preparation is visible. The clinician follows one scanning strategy often enough that the software is not asked to join random patches. Colour, where the scanner provides it, helps the eye separate gingiva, enamel and the margin. It does not prove the mesh is complete. The model has to be turned and inspected, especially at the distal and interproximal surfaces that a glance from the buccal side will flatter.

The bite is a separate capture, not an assumption. A beautiful pair of arches with a wrong occlusion is a bad impression that happens to look clean. Before the file is exported, someone should be able to say that the margin, the contacts and the bite are adequate for the restoration being made. Export in the format the laboratory has agreed, typically STL, or PLY or OBJ when colour is part of the handover.

Only then is there a final digital model. Everything before that is still a draft.

Why Digital Impressions Can Save Time in Everyday Practice

The largest saving is usually the remake you did not book. A silicone impression that leaves the building with a drag, a tear or a bubble gives the time back to nobody: the patient returns, the diary moves, the laboratory waits. A scan that shows the same fault while the patient is present costs a short extra pass.

Other savings are quieter. There is no setting time in the mouth and no disinfection and packaging of a tray for that case. The laboratory can receive the file the same day. Patients who gag on trays often tolerate a tip more easily, which keeps the appointment calmer and, in practice, shorter.

The saving is not automatic. A scanner in untrained hands can make the first month slower. The way through that month is a limited case mix, a repeated path, and permission to rescan a small area without treating it as a failure.

Practices planning the wider change, including when a physical impression should stay, can read our guide to moving from physical to digital impressions.

Digital vs Traditional Impressions: Speed, Comfort and Accuracy

A traditional silicone or other elastomeric impression is a familiar, capable method. Tray selection, material handling, seating pressure and setting time are skills, and many laboratories still produce excellent work from them. The time cost is structural. The material has to work and then set. Removal is a single event. If the margin is not there, the whole impression is repeated. Distortion in transit is a risk the clinic cannot watch.

A digital record moves the quality check forward and removes the setting step. Comfort is better for a large share of patients, especially those with a strong gag reflex, though a scanner tip is still an object in the mouth and some people will dislike it. Accuracy can be excellent when the field is dry, the path is stable and the operator reviews the file. Accuracy is ordinary or poor when those conditions are skipped, even on a scanner with an impressive specification.

Speed, comfort and accuracy are three results, not one. A very fast scan that misses the margin is slower than a careful silicone impression that captured it. The digital advantage appears when speed and review happen together.


Traditional silicone impression

Digital scan

Time in the mouth

Working time plus setting time, then removal

Capture usually measured in seconds to a few minutes, plus review

If a detail is missing

Repeat the impression

Rescan the area

Comfort

Tray and setting material

Tip and a dry field; usually easier for gagging patients

When you know it failed

Often at the laboratory, or on fit

On screen, before the patient leaves

What still takes clinical time

Retraction, isolation, judgement

Retraction, isolation, judgement

Good vs Bad Dental Impression: What Makes the Difference?

A good vs bad dental impression is decided by whether the next person can do their job. The laboratory needs a margin it can follow, contacts it can trust, and a bite that matches the mouth. A file or a tray that merely exists has not met that test.

A good digital impression shows a continuous surface over the preparation, a margin that is not guessed, neighbouring teeth that are stable, and a bite that does not rock when the models are articulated on screen. Soft tissue is out of the way of the line the technician must see. The file has been looked at by someone who is allowed to say it is not ready.

A bad one can be fast, colourful and confidently exported. Holes at the margin, a double image where the patient moved, a bite taken on a partial arch, and a distal surface that fades into nothing are all bad impressions. So is a beautiful scan of the wrong preparation, sent before the dentist has seen it.

Common Causes of Poor Digital Impression Quality

Most poor scans come from a short list of conditions, repeated.

Moisture and blood scatter the image and leave streaks the software may smooth over. An un-retracted margin cannot be scanned into existence. Patient movement creates a fold or a second surface that looks almost anatomical until the model is rotated. A scanning path with large jumps gives the software too little overlap to stitch. Reflective metal and wide edentulous spans remove the landmarks the system uses to stay oriented. A tired laptop drops frames, and the operator blames the handpiece.

There is also a human cause. If the only person who checks the scan is already late for the next patient, small holes get called “fine”. The laboratory then becomes the quality control, which is the expensive version.

How to Improve Accuracy and Reduce the Need for Rescanning

Rescanning falls when the first pass is set up to succeed.

Dry the field and retract the margin the restoration actually requires. Use one scanning path until the team can do it without thinking, then adapt it for the odd case. Watch the screen during the pass, not only at the end, so a hole is filled while the tip is still in the area. Capture the bite as its own step. Rotate the model and name the checks out loud for a while: mesial, distal, buccal, lingual, contacts, occlusion.

Match the scanner and the computer to the manufacturer’s requirements, and keep the optical window clean. Agree with the laboratory which defects they will reject, and treat that list as the clinic’s list too. A ten-second rescan of a margin is a success. A remake appointment is the cost of hoping.

New users should expect more rescans in the first weeks. That is training, not a faulty device. The aim is a routine in which the extra pass is small and rare.

Dental Digital Impressions in the UK: Why More Practices Are Going Digital

What dental digital impressions UK clinics need is the same thing practices elsewhere in Europe need: a file the laboratory will open, and a scanner the team will use on a normal day. They are moving for the same reasons. Patients ask for an alternative to trays. Laboratories increasingly prefer a file they can inspect. Associates move between practices and expect a scanner to exist. The diary argument is the one that convinces an owner: fewer return visits for a missed margin, and a record that can be sent without a courier cutoff.

UK teams comparing equipment should look past the scan-speed claim. Confirm delivery, training, the software licence, the computer specification, and how warranty service works when the supplier is elsewhere in Europe. Voltage and plugs are rarely the issue with a USB scanner. Support and a laboratory that will accept the export are the issue. A demonstration on a UK clinic’s own case mix, including the laboratory that will receive the files, is more useful than a general promise about “going digital”.

Dentiverse works with practices making this change from Europe, including teams in the UK who want a clear route from scanner to laboratory. Panda and Runyes are the budget lines we supply for clinics taking the first step. The right time saving comes from a scanner the staff will use on ordinary crowns, not from the shortest number on a slide.

If you want to time the workflow properly, book a demonstration and bring a typical preparation. We would rather you see how long the impression takes in your hands than quote a figure that only holds on a model.

How long does a dental impression take with a scanner?

Often one to a few minutes for the capture, depending on the arch, the operator and the scanner. Manufacturer examples in our range include about one minute for a full arch on Panda Smart, and about 30 seconds for a single arch or 90 seconds for a full arch with occlusion on the relevant Runyes model. Isolation, bite and review sit on top of that.

Are digital impressions in dentistry as accurate as silicone?

They can be, when isolation, retraction, scanning path and on-screen review are done properly. A fast, unchecked scan is not more accurate because it is digital. A careful conventional impression can still be the better record in a case the scanner has not captured.

What is the difference between a good and a bad dental impression?

A good impression gives the laboratory a clear margin, stable neighbouring surfaces and a reliable bite. A bad one is missing data, distorted by movement or moisture, or sent without anyone checking it. The test is whether the next step can proceed without a repeat.

Do digital impressions suit UK practices that still use an outside laboratory?

Yes. The important check is that the laboratory can open the file format you export and that you both agree what a rejected scan looks like. The scanner should be chosen with that laboratory, not only from a specification table.

Will we save time in the first week?

Possibly not. New users are often slower until the path and the review become routine. The lasting saving is fewer full repeats and faster handover, once that routine exists.